Frequency control Crystal controlled PLL synthesizerTransmit frequency Baby unit: 2405 - 2475 MHzParent unit: 2405 - 2475 MHzChannels 32LCD 5” Color LCD (WQVGA 480x272 pixel)Nominal effective range Actual operating range may vary according to environmental conditions at the time of use.Power requirements Parent unit: 3.6V Ni-MH batteryBaby unit power adapter: Output: 5V DC @ 1AParent unit power adapter: Output: 5V DC @ 1A
Technical specifications
Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license.
The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.
The applied nameplate is located at the bottom of the
baby unit’s base.
When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height
above 2 meters.
4. This product is not a substitute for adult supervision of the
infant. Supervising the infant is the parent’s or caregiver’s
responsibility. This product could cease operating, and
therefore you should not assume it will continue working
properly for any given period of time. Further, this is not
a medical device and should not be used as such. This
product is intended to assist you in supervising your baby.
5. Do not use this product near water. For example, do
not use it next to a bath tub, wash bowl, kitchen sink,
laundry tub or swimming pool, or in a wet basement
or shower.
6. CAUTION: Use only the battery provided. There may be a
risk of explosion if a wrong type of battery is used for the
parent unit. The battery cannot be subjected to high or low
extreme temperature and low air pressure at high altitude
during use, storage or transportation. Disposal of battery
into fire or a hot oven, or mechanically crushing or cutting or
the battery can result in an explosion. Leaving the battery in
an extremely high temperature surrounding environment
can result in an explosion or the leakage of flammable liquid
of gas. Battery subjected to extremely low air pressure may
result in an explosion or the leakage of flammable liquid or
gas. Dispose of used battery according to the information in
The RBRC
®
seal.
7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Baby unit power adapter: Output: 5V DC 1A;
Parent unit power adapter: Output: 5V DC 1A.
8. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it
is plugged into a ceiling, under-the-table or cabinet
outlet.
9. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
10. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth
for cleaning.
11. Do not cut off the power adapters to replace them with
other plugs, as this causes a hazardous situation.
12. Do not allow anything to rest on the power cords. Do
not install this product where the cords may be walked
on or crimped.
13. This product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply in your home,
consult your dealer or local power company.
14. Do not overload wall outlets or use an extension cord.
15. Do not place this product on an unstable table, shelf,
stand or other unstable surfaces.
16. This product should not be placed in any area where
proper ventilation is not provided. Slots and openings
in the back or bottom of this product are provided for
ventilation. To protect them from overheating, these
openings must not be blocked by placing the product
on a soft surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or heat
register.
17. Never push objects of any kind into this product
through the slots because they may touch dangerous
voltage points or create a short circuit. Never spill liquid
of any kind on the product.
18. To reduce the risk of electric shock, do not
disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the
product other than specified access doors may
expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock
when the product is subsequently used.
19. You should test the sound reception every time you
turn on the units or move one of the components.
20. Periodically examine all components for damage.
21. There is a very low risk of privacy loss when using
certain electronic devices, such as baby monitors,
cordless telephones, etc. To protect your privacy,
make sure the product has never been used before
purchase, reset the baby monitor periodically by
powering off and then powering on the units, and
power off the baby monitor if you will not use it for
some time.
22. Children should be supervised to ensure that they do
not play with the product.
23. The product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between
0
o
C and 40
o
C.
2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to a
heating source.
3. Batteries should not be exposed to excessive heat such
as bright sunshine or fire.
4. Make sure the baby unit(s) and the
adapter cord(s) are always out of reach
of the baby, at least 3 feet away from
the baby or crib, to avoid a possible
strangulation hazard.
5. Never place the baby unit(s) inside the baby’s crib or
playpen. Never cover the baby unit(s) or parent unit
with anything such as a towel or a blanket.
6. Other electronic products may cause interference
For operations and guides to help you using your video monitor, and for latest information and supports, go and check the online help topics and online FAQs.Use your smartphone or mobile device to access our online help.
• Go to https://auphones.vtech.com/baby-safe-and-sound/
video-monitors/478; ORScan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help. -If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.You can also call our Customer Support at 1300 369 193.
S
m
BM4700
Full Color Pan and Tilt Video MonitorGo to auphones.vtech.comfor the latest VTech product news.
NOTESNOTE
• The rechargeable battery in the parent unit is built-in.• Use only the power adapters supplied with this product.• Make sure the baby monitor is not connected to a switch-controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.• Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.Slide the switchto power on or off your baby unit.Press and hold POWER to power on or off your parent unit.Adjust speaker volume
Press / to adjust your parent unit
speaker volume.
Zoom
Press to zoom in or out.Talk to your baby unitPress and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when finish talking and hear your baby again.
63ē
Turn off the screenPress and hold LCD ON/OFF to switch off the screen. You can still hear sound from the baby unit.
Tip
• Press any keys on the parent unit to turn on the screen again.
Press and hold
Use the menuPress to enter the menu, choose a menu item, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby unit lullaby, or to adjust the baby unit sound sensitivity.While in the menu:
• Press or to scroll among the menu options.
• Press to select an item, or to save a setting. • Press or to scroll among the sub-menus, or to adjust a setting.• Press to return to the previous menu options without changing the current setting.
• Press /EXIT to return to live video.
Quick start guide
x 2
x 2
4
Status check
3
Positioning the baby monitor
Caution• The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience high-pitched screeching noise from your baby monitor while positioning: -Make sure your baby unit and parent unit are more than 1 metre apart, OR -Lower the volume of your parent unit.
NOTESNOTE
Note
• To avoid interference from other electronic devices, place your baby monitor at least 1 metre away from devices such as wireless routers, microwaves, cell phones and computers.
Parent unit icons
63ē
ē
63ē
≥
<
3ft (1m)
3ft (1m)
63ē
﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏﹏﹏﹏﹏﹏
﹏﹏﹏
﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
Long press
Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the
baby’s cot or playpen.
> 3ft (1m)
>
<
3ft (1m)
3ft (1m)
63
ē
63
ē
Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on. The ON LED light of baby unit turns on.Main
menu
Sub-menuBrightness• Adjust the parent unit’s LCD brightness.Camera settingsBaby unit speaker volume• Adjust the baby unit’s speaker volume.Monitoring mode (For pairing with BM5710 only)• Single mode• Split mode• Patrol modeAdd a baby unit (For pairing with BM5710 only).Delete a baby unit.Lullaby/ Play/Stop lullaby• Select one of the soothing sounds, or white noise.• Select one of the five melodies.• Play all melodies.• Set timer to stop playing the selected melody or soothing sound.Main
menu
Sub-menuNight light
/
Turn on/off night light• Select one of the night light colors.• Set timer to turn the night light off.• Set to auto turn on the night light when baby unit detects sound. It will turn off after 15 minutes of no sound detection. You can set VOX sensitivity level to detect sounds that exceed certain levels. See Sound sensitivity and sound activation section. Projection light
/
Turn on/off projection light• Set timer to turn the projection light off.• Set to auto turn on the projection light when baby unit detects sound. It will turn off after 15 minutes of no sound detection. You can set VOX sensitivity level to detect sounds that exceed certain levels. See Sound sensitivity and sound activation section. Alert settings• Set the parent unit to beep when the battery is low.• Set the parent unit to beep when the link between the parent unit and the baby unit is lost. • Set the confirmation tone on or off when selecting an option in the menus.• Set the parent unit to beep when the baby unit detects sounds while in Split mode (For pairing with BM5710 only).
/
• Turn on/off the alert vibration.Main
menu
Sub-menuTemperature
/
• Turn on/off temperature alert tone.• Set the parent unit to beeps whenever the room temperature detected by the baby unit falls outside of the set temperature range.• Set the minimum temperature.• Set the maximum temperature.• Set temperature display in Fahrenheit
(
o
F) or Celsius (
o
C)
Sound activation - screen and audio
/
Turn on/off sound activation• Set sound activation on or off.• When it is on, and the baby unit detects no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection.
NOTESNOTE
Note
• When the parent unit screen is off and it receives alerts, for example, link lost between parent unit and baby unit, or battery is low, the parent unit screen and speaker will turn on for 10 seconds.VOX (Voice Activated Alert) Sensitivity
• You can set VOX sensitivity level to activate parent unit screen and sound when baby unit detects sounds that exceed certain levels. See Sound sensitivity and sound activationsection.
Main menu icons
7Arrow keys• While viewing image from the baby unit, press to pan and tilt the baby unit leftward, upward, rightward or downward.
8
Volume 9VIEW /LCD ON/OFF
10
/EXIT11Antenna12RESET13Stand14Power jack
Power on
Power off
5
7
8
9
12
10
11
14
3
4
2
1
6
13
5
7
8
9
12
10
11
14
3
4
2
1
6
13
5
7
8
9
12
10
11
14
3
4
2
1
6
13
1Light sensor2Camera lens3Microphone4Night light5On/Off switch6On/Off LED light • On when the baby unit is turned on and is paired to the parent unit.• Flashes when the baby unit is not being viewed; or when the link to the parent unit is lost.7Projection light8Speaker
9
Projection light on/off key
10
Night light on/off key11Power jack12Temperature sensor13PAIR key14Slots for wall mounting
Long press
Power off
Long press
Power on
Quick start guide
For more support information
S
m
Ver el manual de Vtech BM4700 aquí, gratis. Este manual pertenece a la categoría monitores para bebés y ha sido calificado por 1 personas con un promedio de 7.5 . Este manual está disponible en los siguientes idiomas: Inglés . ¿Tienes alguna pregunta sobre Vtech BM4700 o necesitas ayuda? Haz tu pregunta aquí
¿Necesitas ayuda?
¿Tiene alguna consulta sobre el Vtech y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Vtech proporcionarle una buena respuesta.
¿No puede encontrar la respuesta a su consulta en el manual? Puede encontrar la respuesta a su consulta en las preguntas frecuentes sobre el Vtech BM4700 más abajo.
¿El manual de Vtech BM4700 está disponible en Español?
Por desgracia, no tenemos el manual de Vtech BM4700 disponible en Español. Este manual está disponible en Inglés.
¿Necesitas ayuda?
¿Tiene alguna consulta sobre el Vtech y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Vtech proporcionarle una buena respuesta.
Número de preguntas: 0